BLAST POT, STATIONARY, 10.0 CU FT, 2 OUTLET, PRESSURE RELEASE, ELECTRIC, (2)APV II W/TC SLEEVE/COMBINATION VALVE, 1-1/2" PIPING / 2" INLET

! WHEN USING STEEL ABRASIVES, ELECTRIC CONTROL HANDLE #2 (888-2263-401PB) AND SEALED CONNECTOR(S) (PB-31131) ARE REQUIRED

VIDEO - BIG GUN VS STANDARD BLAST POT DEMONSTRATION

FEATURES & BENEFITS OF SPR ELECTRIC STATIONARY BIG GUN FULL FLOW

A. 10.0 CU. FT. CAPACITY (285 LITERS)
     1. 150 PSI VESSEL (10.3 BAR)
     2. A.S.M.E. SECTION VIII DIVISION 1
     3. CRN FOR ALL PROVINCES
B. PRESSURE RELEASE SYSTEM
     1. AUTOMATICALLY BLOWS DOWN THE VESSEL WHEN CONTROL HANDLE IS RELEASED
     2. LOW MAINTENANCE DESIGN
     3. SIMPLE TROUBLE SHOOTING FOR IN FIELD REPAIRS
C. ELECTRIC CONTROLS 12VDC
     1. WHEN RUNNING OVER 100 FEET OF BLAST HOSE THIS ADDS ADDITIONAL SPEED TO STOPPING & STARTING THE BLASTING OPERATION
     2. HELPS WITH FREEZING PROBLEMS IN COLD WEATHER
     3. HEAvY DUTY FILTERED CONTROL VALVE REDUCES STOPPING TIME WHEN CONTROL HANDLE IS RELEASED
D. BIG GUN FULL FLOW SYSTEMS PROVIDES
     1. A ZERO PRESSURE DROP PATH FOR AIR & ABRASIVE TO TRAVEL TO THE BLAST NOZZLE FOR EVERY 1 PSI GAINED OR LOST IN ABRASIVE BLASTING = 1.5% PRODUCTION
     2. A MUST FOR #7 & #8 NOZZLES
     3. FULL PORT COUPLING BLAST HOSE CONNECTION PROVIDES AN UNRESTRICTED PATH FOR AIR & ABRASIVE TO TRAVEL TO THE NOZZLE
E. 800 CFM MOISTURE SEPARATOR UPGRADE AVAILABLE (NOT INCLUDED)
F. 1-1/2" GALVANIZED PIPING FOR CORROSION RESISTANCE / 2" INLET
G. HEAVY DUTY FULL PORT BALL VALVES
H. EXTENDED LIFE SCHEDULE 80 HEAVY DUTY NIPPLE
     1. WITHSTANDS ABRASIVE WEAR FOR LONGER LIFE
I. BOLT CLAMPS ON PUSHER LINE MAKE FIELD REPAIRS EASIER
J. COMBINATION VALVE/MPV VALVE
     1. COMBINATION VALVE IS A 2 IN 1 DESIGN THAT WILL STOP THE AIR BLASTING AND RELIEVES THE PRESSURE FROM THE VESSEL WHEN THE CONTROL HANDLE IS RELEASED
     2. MANUAL PLUNGER VALVE (MPV) IS A SIMPLE RELIABLE DESIGN THAT PROVIDES A WIDE RANGE OF ADJUSTMENT OF ABRASIVE FLOW TO THE NOZZLE
K. 15' BLOWDOWN HOSE ASSEMBLY FOR REMOTE MOUNTING
L. 9" ADJUSTABLE SPIDER
     1. FULLY ADJUSTABLE FOR DIFFERENT MEDIA TYPES & SIZES
     2. WHEN ABRASIVE IS HOPPER FEED FROM ABOVE THIS KEEPS THE WEIGHT OF THE ABRASIVE OFF THE POP-UP ALLOWING IT TO CLOSE & SEAL PROPERLY
M. SKIRTED POP-UP GASKET
     1. SKIRTED POP-UP GASKET BY DESIGN WILL KNIFE ITS WAY THROUGH THE ABRASIVE TO ASSIST IN SEALING
     2. HELPS WITH THE ABRASIVE BURPING PROBLEM THAT IS COMMONLY SEEN WITH HOPPER FEED BLAST POTS
     3. A MUST WHEN USING LARGE GRIT SIZES
N. UNION END BALL VALVES
     1. ALLOW YOU TO SHUT OFF THE ABRASIVE AT THE BOTTOM OF THE POT FOR MAINTENANCE OR REPAIRING THE ABRASIVE METERING VALVE WITHOUT DUMPING THE ENTIRE VESSEL OF ABRASIVE ON THE FLOOR
O. FULL LOAD LIFTING EYES
     1. ALLOW LIFTING AND TRANSPORTATION OF VESSEL FOR PLACEMENT MAINTENANCE OR REPAIR