BLAST POT, STATIONARY, 6.5 CU FT, SHORT-CYCLE - PRESSURE RELEASE, PNEUMATIC, 54" OAH

SHORT-CYCLE SYSTEM SAVER
     SHORT-CYCLE BLASTERS ARE DESIGNED TO WITHSTAND THE PUNISHING EFFECTS OF QUICK ON-OFF BLASTING WHILE RETAINING THE CONVENIENCE OF A PRESSURE RELEASE SYSTEM. STANDARD PRESSURE RELEASE (SPR) BLASTERS ARE GREAT FOR BLAST ROOMS BECAUSE WHEN PAIRED WITH AN OVERHEAD ABRASIVE HOPPER, THEY CAN BE REFILLED BY SIMPLY RELEASING THE CONTROL HANDLE AND ALLOWING THE BLASTER TO DEPRESSURIZE AND AUTOMATICALLY FILL. UNFORTUNATELY, WHEN BLASTING FREQUENTLY FOR LESS THAN 10 MINUTES AT A TIME, ABRASIVE CAN OVERFILL THE BLASTER, DAMAGING THE POP-UP AND CAUSING IT NOT TO SEAL PROPERLY. THIS CAUSES ABRASIVE TO"BURP" FROM AROUND THE POP-UP AND EVENTUALLY RUIN THE METERING VALVE.
      PIRATE BRAND SHORT-CYCLE BLASTERS OVERCOME THIS ISSUE BY REMAINING PRESSURIZED WHEN THE CONTROL HANDLE IS RELEASED BUT FEATURE A REMOTE BLOW-DOWN BUTTON TO ALLOW YOU TO DEPRESSURIZE/REFILL YOUR BLASTER WITHOUT LEAVING THE BLAST ROOM.

VIDEO - BIG GUN VS STANDARD BLAST POT DEMONSTRATION

FEATURES & BENEFITS OF SHORT-CYCLE - SPR PNEUMATIC STATIONARY W/ BIG GUN FULL FLOW SYSTEM

A. 6.5 CU. FT. CAPACITY (185 LITERS)
     1. 150 PSI VESSEL (10.3 BAR)
     2. A.S.M.E. SECTION VIII DIVISION 1
     3. CRN FOR ALL PROVINCES
B. SHORT CYCLE PRESSURE RELEASE SYSTEM
     1. AUTOMATICALLY BLOWS DOWN THE VESSEL WHEN PALM BUTTON CONTROL IS ACTIVATED
     2. LOW MAINTENANCE DESIGN
     3. SIMPLE TROUBLE SHOOTING FOR IN FIELD REPAIRS
C. BIG GUN FULL FLOW SYSTEMS PROVIDES
     1. A ZERO PRESSURE DROP PATH FOR AIR & ABRASIVE TO TRAVEL TO THE BLAST NOZZLE FOR EVERY 1 PSI GAINED OR LOST IN ABRASIVE BLASTING = 1.5% PRODUCTION
     2. A MUST FOR #7 & #8 NOZZLES
     3. FULL PORT COUPLING BLAST HOSE CONNECTION PROVIDES AN UNRESTRICTED PATH FOR AIR & ABRASIVE TO TRAVEL TO THE NOZZLE
D. HEAVY DUTY MOISTURE SEPARATOR
E. 1-1/2" GALVANIZED PIPING FOR CORROSION RESISTANCE
F. HEAVY DUTY FULL PORT BALL VALVES
G. EXTENDED LIFE SCHEDULE 80 HEAVY DUTY NIPPLE
     1. WITHSTANDS ABRASIVE WEAR FOR LONGER LIFE
H. BOLT CLAMPS ON PUSHER LINE MAKE FIELD REPAIRS EASIER
I. APVII/COMBINATION VALVE
     1. AUTOMATIC PLUNGER VALVE II (APVII) PREMIUM ABRASIVE METERING VALVE WITH QUADRUPLE PLUNGER SEAL ARRANGEMENT SOLVES THE AIR & ABRASIVE CARRY OVER PROBLEM AS WELL AS THE PLUNGER & SEAL JAMMING PROBLEM NORMALLY ASSOCIATED WITH REGULATED LOW PRESSURE BLASTING APPLICATIONS AND OR THE USE OF STEEL ABRASIVE. SOLID MACHINED TUNGSTEN CARBIDE PLUNGER & SLEEVE PROVIDES FAR SUPERIOR WEAR RATES AND 100% CONSISTENT TOLERANCES. 1" NPT CLEANOUT PORT GIVES ACCESS TO OBSTRUCTIONS THAT MAY BE BRIDGING OVER THE METERING PORT ALSO ALLOWS YOU TO DRAIN THE VESSEL WITHOUT REMOVING THE VALVE.
     2. COMBINATION VALVE IS A 2 IN 1 DESIGN THAT WILL STOP THE AIR BLASTING AND RELIEVES THE PRESSURE FROM THE VESSEL WHEN THE PALM BUTTON IS ACTIVATED
     3. RELIEVING CONTROL HANDLE REDUCES AIR CONSUMPTION AND REDUCES STOPPING TIMES WHEN CONTROL HANDLE IS RELEASED
J. 15' BLOWDOWN HOSE ASSEMBLY FOR REMOTE MOUNTING
K. 9" ADJUSTABLE SPIDER
     1. FULLY ADJUSTABLE FOR DIFFERENT MEDIA TYPES & SIZES
     2. WHEN ABRASIVE IS HOPPER FEED FROM ABOVE THIS KEEPS THE WEIGHT OF THE ABRASIVE OFF THE POP-UP ALLOWING IT TO CLOSE & SEAL PROPERLY
L. SKIRTED POP-UP GASKET
     1. SKIRTED POP-UP GASKET BY DESIGN WILL KNIFE ITS WAY THROUGH THE ABRASIVE TO ASSIST IN SEALING
     2. HELPS WITH THE ABRASIVE BURPING PROBLEM THAT IS COMMONLY SEEN WITH HOPPER FEED BLAST POTS
     3. A MUST WHEN USING LARGE GRIT SIZES
M. UNION END BALL VALVES
     1. ALLOW YOU TO SHUT OFF THE ABRASIVE AT THE BOTTOM OF THE POT FOR MAINTENANCE OR REPAIRING THE ABRASIVE METERING VALVE WITHOUT DUMPING THE ENTIRE VESSEL OF ABRASIVE ON THE FLOOR
N. FULL LOAD LIFTING EYES
     1. ALLOW LIFTING AND TRANSPORTATION OF VESSEL FOR PLACEMENT MAINTENANCE OR REPAIR